How To Install New Hard Drive In Imac

Introduction

Upgrade your hard bulldoze for more storage space!

This guide also includes steps to upgrade your iMac'due south hard drive with a SSD. It describes how to install the SSD'south temperature sensor so that the Mac'due south fans volition operate at the correct speed.

Before kickoff whatsoever work on your iMac: Unplug the calculator and press and hold the ability button for ten seconds to discharge the power supply's capacitors.

Exist very conscientious not to touch on the capacitor leads or any exposed solder joints on the back of the power supply.

• Stick a heavy-duty suction cup near each of the ii top corners of the glass panel.

• To adhere the suction cups, first position the suction loving cup with the movable handle parallel to the face up of the glass panel (as highlighted in the second film).

• While lightly property the suction cup confronting the drinking glass, enhance the movable handle until it is parallel with the other handle (as highlighted by the tertiary picture).

• If your suction cups refuse to stick, effort cleaning both the glass console and the suction loving cup with a clammy soft, lint-free cloth. (Dampen with distilled water, and if needed, an equal ratio of distilled water and white vinegar for best results.)

• Practise not use the suction cups to carry the display drinking glass considering if 1 of them fails to stick, you could drop the screen and break information technology.

• The original iMac box makes a good place to store the glass console. Otherwise, a padded horizontal surface, like a towel on a desk will do nicely.



• Gently elevator the glass panel perpendicular to the face of the LCD enough to clear the steel mounting pins attached along the underside of the acme edge of the glass panel.

• Pull the glass panel abroad from the lower edge of the iMac and carefully set it bated.

• Don't utilise the suction cups to carry the glass panel—if either one loses its grip, the panel could fall and break.

• Afterwards setting the glass panel down safely, be sure to release the suction cups, as the suction force over time can crack the glass.

• During reinstallation, be sure to meticulously clean the within of the glass console and the face of the LCD as any dust or fingerprints trapped inside will be annoyingly visible when the machine is turned on.

• Remove the eight T10 Torx screws securing the LCD to the outer case.

• Carefully lay the iMac stand-side downwardly on a flat surface.

• Due to tight tolerances, y'all will accept to employ a thin hooked tool to lift the display out of the outer case. As seen in the third moving-picture show, we made i out of a aptitude paperclip.

• Use a thin hooked tool to lift one side of the top edge of the brandish past its steel outer frame.

• After lifting the meridian edge of the brandish on one side, hold it out of the outer example while y'all utilise a hooked tool to elevator the other side. A pencil or pen can be placed under the acme edge of the display, parallel to the elevation edge and extending past the border of the reckoner, to go on the first side propped up while lifting the second.

• Practice not lift the tiptop border of the brandish out of the outer case too far, as several short ribbon cables still connect the two components.

• Use a pair of tweezers to pull the vertical sync ribbon cable out of its socket on the LED driver board well-nigh the top left corner of your iMac.

• On some iMacs this may not be a ribbon cable simply four dissever, very fine and very fragile wires. Be very careful, if the tweezers slip off the plug, you will very likely pull a wire out of the assembly.

• Rotate the brandish out of the outer case enough to disconnect the LED backlight ability cablevision from the LED driver board.

• Squeeze the two display data cable connector arms together to unlock it from its socket on the logic lath.

• Pull the display data cablevision connector abroad from its socket on the logic board.

• Be very careful when disconnecting this cable as both the cablevision connector and logic lath socket are extremely fragile. When reconnecting the cable later on, use as niggling force as possible.

• Lift the display for plenty clearance to disconnect the LCD thermal sensor cable connector from its socket on the logic board.

• If your fan is spinning full speed later on completion, check this connection or the hard drive's thermal sensor cable. The thermal sensor connector socket is very frail, so be very careful when you connect back the sensor cable.

• Carefully pull the display toward the summit edge of your iMac and lift information technology out of the outer example.

• Earlier disconnecting the thermal sensor cablevision, have note of its orientation. It is extremely of import to reinstall the connector in the electric current orientation so the fans will not run at full speed. If you have multiple pins on your replacement hard bulldoze, put the connector closest to the SATA connections and closest to the PCB board.

• Disconnect the thermal sensor, SATA power, and SATA data cables by pulling their connectors away from the sockets on the hard drive.

• Remove the two T10 Torx screws securing the upper hard drive subclass to the outer instance.

• Slightly rotate the hard bulldoze away from the outer case.

• Lift the hard drive off its two lower positioning pins and remove it from the outer example.

• Remove the two T8 Torx screws securing the upper bracket to the hard drive.

• Remove the upper bracket from the hard drive.

• Remove the two T8 Torx pins from the other side of the hard bulldoze.

• Carefully peel off the piece of EMI cream attached to the front end of the hard bulldoze.

• Don't forget to transfer this to your new difficult drive.

• Follow the next steps if you lot are replacing your difficult drive with an SSD kit.

• If your SSD enclosure looks like the first epitome, follow this guide instead.

• Line up the SSD connectors with the metal enclosure's sockets.

• Press the bulldoze confronting the enclosure sockets until the SSD is firmly seated.

• The SSD connects with the enclosure in only one direction. If the connectors don't line up, rotate the SSD and endeavour over again.

• Use a Phillips screwdriver to install the four silver screws (ii on each side) along the edges of the SSD to secure it to the enclosure.

• Plug the included sensor-enabled SATA power cable into the enclosure's port.

• The cable is keyed to connect in but ane orientation. If yous can't connect the cable, rotate information technology 180° and try again.

• Peel the white liner off the back of the pocket-size temperature sensor board in gild to betrayal the adhesive.

• Attach the temperature sensor board to an exposed, metal surface of the SSD, close to the SATA connector.

• Fold the excess temperature sensor wires so that they are out of the way while you lot install the enclosure.

• Use a T8 commuter to install the mounting pins from the old difficult drive onto the sides of the enclosure.

• Attach any mounting brackets removed from the old hard bulldoze onto the enclosure.

• Connect the iMac's SATA power cable to the other cease of the new sensor-enabled SATA cable.

• Connect the iMac's SATA data cable to the enclosure's socket.

• The images used in this step come from a 2022 iMac. Your cables may await slightly different, only the procedure remains the same.

• Slide the SSD enclosure into the space previously occupied past the difficult drive.

• Route the SATA cables so that they volition not interfere with any other components.

• Effort to keep the cables free from whatever abrupt bends, and route them such that they are not pinched.

• If your motherboard has a socket for a hard drive temperature sensor, follow this stride to plug the sensor wires in.

• Find the connector on the motherboard labeled Hd TMP or HDD TEMP.

• If you take trouble locating it, trace the ii-wire temperature cablevision yous disconnected from the former difficult drive.

• If the previous temperature cable is still connected to the lath here, disconnect and remove it. You will no longer need it.

• Connect the temperature sensor'due south two-wire red-black cable to the motherboard plug labeled Hard disk TMP or HDD TEMP.

• The connector is keyed to fit in only one orientation. If it doesn't fit one way, rotate it 180° and attempt over again.

• Route the excess wire so it does non interfere with any other components.

Conclusion

To reassemble your device, follow these instructions in opposite order.

Embed this guide

Choose a size and copy the code below to embed this guide as a small widget on your site / forum.

Preview

Source: https://www.ifixit.com/Guide/iMac+Intel+27-Inch+EMC+2309+and+2374+Hard+Drive+Replacement/1634

Posted by: alvaradogonell.blogspot.com

Share this post